how to strip and refinish a wood floor

How To Strip And Refinish A Wood Floor. That's 600 square feet, or $600 if you do it yourself versus perhaps $2,400 if. You barely have to even go over the floor.

Pin on Porch from www.pinterest.com

Caulk left on the floor becomes sandwiched between the wood and paint and will move independently, causing the paint to crack. (again i left it overnight). Sanding and refinishing hardwood floors costs $1.50 to $5.00 per square foot for labor and materials.

Source: www.pinterest.com

The hardwood floor refinishing process is easier and less expensive than sanding down to bare wood and takes less. Never sand it or the look of the floor will be ruined.

Source: www.pinterest.com

An orbital or belt sander also won't reach the edges properly. To buff out a small scratch in your floor polish by hand, rub brass wool over the damage until the scratch or ding has been leveled out and you can't see it anymore.

Source: www.pinterest.com

After sanding, contractors apply multiple coats of clear finish seal and protect the floor. When you reach the wall, return to the center of the room and sand the next section, until you sand the entire wood floor.

Source: www.pinterest.com

Go over the whole floor and set all nails below the surface of the wood, but don't fill them. Apply the solvent with a rag to loosen the shellac/lacquer from the wood surface, then lightly scrape the residual finish with a plastic putty knife.

Source: www.pinterest.com

To buff out a small scratch in your floor polish by hand, rub brass wool over the damage until the scratch or ding has been leveled out and you can't see it anymore. You barely have to even go over the floor.

Source: www.pinterest.com

Let's consider a room that's 30 feet by 20 feet. Apply 1 coat of bona novia (satin).

Source: www.pinterest.com

If you do it yourself, it will cost about $1 per square foot. An orbital or belt sander also won't reach the edges properly.

Source: www.pinterest.com

When you reach the wall, return to the center of the room and sand the next section, until you sand the entire wood floor. That's 600 square feet, or $600 if you do it yourself versus perhaps $2,400 if.

Source: www.pinterest.com

Deciding whether to refinish or replace the wood floor in your home? The cost for having a professional refinish a hardwood floor runs about $3.50 to $4 per square foot.

Source: www.pinterest.com

A drum sander will only get to within a few inches of your walls. Never sand it or the look of the floor will be ruined.

Source: www.pinterest.com

The cost for having a professional refinish a hardwood floor runs about $3.50 to $4 per square foot. Sanding removes the old finish and the surface layer of the wood to eliminate scratches, dings, and discoloration.

Source: www.pinterest.com

Vacuum the floor again and sand it. It is fine to paint over the caulk between the boards.

It is fine to paint over the caulk between the boards.

To buff out a small scratch in your floor polish by hand, rub brass wool over the damage until the scratch or ding has been leveled out and you can't see it anymore. That's 600 square feet, or $600 if you do it yourself versus perhaps $2,400 if. When you reach the wall, return to the center of the room and sand the next section, until you sand the entire wood floor.

Apply the solvent with a rag to loosen the shellac/lacquer from the wood surface, then lightly scrape the residual finish with a plastic putty knife.

Expect to spend in the ballpark of: There are pros and cons to either choice. Caulk left on the floor becomes sandwiched between the wood and paint and will move independently, causing the paint to crack.

An orbital or belt sander also won't reach the edges properly.

Properly applied, the caulk will. (again i left it overnight). If you do it yourself, it will cost about $1 per square foot.

Deciding whether to refinish or replace the wood floor in your home?

Whether you've been admiring your old wood floor for years or you just discovered it hidden under some old carpeting, refinishing it can be a feast for. Turn on the sander and slowly work it back and forth across the entire room. Again make sure you do this slowly and methodically, going around the edge of the floor with the pipe of.

Let's consider a room that's 30 feet by 20 feet.

After sanding, contractors apply multiple coats of clear finish seal and protect the floor. Allow to dry 3 hours. The purpose of this is to key the surface to allow the new coat to bond to the floor and prevent the new coat peeling off.